Skip to main content

Filter By:

  • Show More Sizes
  • Show Fewer Sizes

Indoor Cycling

Tacx Roller Drive Belt
$14.61
Replacement roller belt for Tacs roller trainers.
Tacx Quick Release for Rear Wheel
$17.85
Universal quick release skewer for placing your bike in the trainer or direct drive. This axle replaces the standard quick release, allowing racing bikes and mountain bikes to be used with Tacx trainers.
Tacx Axle Nuts
$29.88
Use these axle nuts to put a city or track bike in a Tacx trainer. The available axle nuts are M10x1 (T1415) and 3/8 Shimano Nexus (T1416). For use with Tacx classic trainers only
Tacx Towel
$29.88
This narrow towel was developed specifically for indoor bike training sessions and is used by many professional riders during their warm-up or indoor training sessions. - Highly absorbent - Measures 30cm x 115cm
Tacx Skyliner
$29.99
The Skyliner is a front wheel support for use with Tacx classic trainers. It raises and supports the front wheel for a natural cycling position and increased stability. It also serves as a handle to carry the trainer.
Tacx E-Thru Trainer Axle
$44.99 - $59.99
The E-Thru Trainer Axle allows the use of a mountain bike in a Tacx trainer. These axles are only suitable for Tacx classic trainers.
Robert Axle Project Trainer Thru Axle
$54.00 - $68.23
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Robert Axle Project Trainer Thru Axle for Surly MDS/Gnot-Boost
$54.00
Our Trainer Axle is designed to adapt your Surly MDS/Gnot Boost thru-axle-equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - This axle is for Surly bikes with the MDS/Gnot Boost system. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum, and hard-anodized for rugged durability. - No special tools required. Design allows for wheel installation or removal using your standard 5 mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
Tacx Trainer Tire 29-inch
$57.18
The Tacx trainer tires have been developed specifically for riding indoors on bike trainers. The special rubber minimizes the risk of overheating, slipping, and wear and tear. They are also quieter than regular rear tires on both road and mountain bikes. Tacx trainer tires are not suitable for outside riding.
Tacx Trainer Tire 700
$57.18
The Tacx trainer tires have been developed specifically for riding indoors on bike trainers. The special rubber minimizes the risk of overheating, slipping, and wear and tear. They are also quieter than regular rear tires on both road and mountain bikes. Tacx trainer tires are not suitable for outside riding.
Tacx Trainer Adapter for X-12 Axle
$59.99
The Trainer Adapter for X-12 Axle allows the use of mountain bikes with axle widths of 142mm or larger on a Tacx trainer. These adapters are only suitable for the Tacx classic trainers.
Kinetic 12mm Traxle Through-Axle
$61.58
Kurt Kinetic's 12mm Traxle Through-Axle lets you attach your mountain bike to a Kinetic trainer without changing the original skewer. The Kinetic Traxle comes in 3 thread pitches: - T-2101 Coarse: M12 x 1.75mm - T-2102 Medium: M12 x 1.5 - T-2100 Fine: M12 x 1.00mm (Fine XL has the same thread pitch and is a longer version of the fine Traxle)
Tacx Direct Drive Quick Release with Adapter Set
$69.99
Use these quick releases to put a racing bike with disc brakes or a mountain bike with a quick-release skewer in a Tacx direct drive trainer. Both axles are supplied with an adapter set so you can select the right combination for your bike. These axles are only suitable for the Tacx direct drives.
Kinetic New Small Wheel Adapter
$73.48
This is the new small wheel adapter for use on newer Kinetic trainer models. A must for BMX, recumbents, and any bike with tires having an outside diameter of 22-inches or less. The small wheel adapter raises the level of the resistance unit of any of the Kinetic Trainers by up to three inches. In doing so, the trainer will fit tires with outside diameters as small as 16-inches. By using this adapter, Kinetic trainers accommodate most BMX, kids', and recumbent bikes. - Compatible with T-2xxx two-thousand series and T-6xxx six-thousand series trainers - Not compatible with 24-inch bicycles
Tacx Trainer Bag
$99.99
Give your Tacx trainer the best possible protection for storage and transport with this sturdy trainer bag. It's designed specifically for Tacx trainers and has a separate compartment on the inside for accessories. The double inner layer with foam lining provides optimum protection, minimizing the risk of damage.
Tacx Direct Drive Freehub Body, Campagnolo
$103.98
This freehub body enables you to fit a Campagnolo cassette on the NEO Smart and the FLUX Smart. Suitable for 9 through 11 speed Campagnolo cassettes. How to place the Campagnolo Body: 1. Remove the cap with a 5-millimeter Allen key. 2. Replace the Shimano/SRAM body with the Campagnolo body. 3. Place the cap on the Campagnolo body and tighten with a 5-millimeter Allen key.
Tacx USB ANT+ Antenna
$103.98
Use this ANT+ antenna to connect an ANT+ trainer to your computer. That enables you to use computer software during your training sessions, such as the Tacx Trainer software, Zwift, and TrainerRoad. These programs read the training data transmitted by an ANT+ trainer and can control the trainer. It features a long cable so the receiver can be placed close to the trainer for an optimal reception without loss. The antenna is compatible with all trainers that communicate wirelessly via ANT+.
Tacx BlackTrack
$249.99
The BlackTrack replaces the Skyliner (front wheel support) and enables you to steer freely in the Tacx Trainer software 4, Advanced. The front wheel of the bike is placed on a turntable so that you can steer to the left and the right. This allows you to choose where to ride when you are training in the virtual worlds. The BlackTrack communicates wirelessly with the computer via ANT+. Rubber Caps on the bottom prevent sliding and reduce noise. This steering frame is foldable. lightweight, and easy to store. The BlackTrack is suitable for the Tacx Trainer software (Windows PC) and can communicate with ANT+ trainers and interactive Smart trainers: - T1980 Bushido (ANT+) - T2020 i-Genius - T2050 Tacx IRONMAN trainer - T2060 Tacx IRONMAN Smart - T2080 Genius Smart with Upgrade Smart - T2170 i-Vortex - T2180 Vortex Smart with Upgrade Smart - T2240 Flow Smart with Upgrade Smart - T2780 Bushido Smart with Upgrade Smart
Tacx NEO Track
$249.99
The NEO Track replaces the front wheel support of the NEO and enables you to steer freely in the Tacx Trainer software 4, Advanced (Windows PC). The front wheel of the bike is placed on a turntable so that you can steer to the left and the right. This allows you to decide yourself where to go to when training in virtual worlds. The NEO Track is only suitable for the NEO Smart in combination with the Upgrade Smart (Tacx Trainer software 4, Advanced and ANT+ antenna required). - Communicates wirelessly with the computer via ANT+ - Rubber caps on the bottom prevent sliding and reduce noise - Foldable, lightweight and easy to store
Tacx Antares
$299.98
With the Antares roller you can cycle freely to refine your coordination and technique. This roller can be retracted to 80 cm. Conical Rollers The Tacx rollers are conical which ensure that your bike always remains in the middle of the roller while you are riding. This makes riding on the rollers easier and safer. Retractable The Tacx rollers are retractable to 80cm. FEATURES Type of trainer: Roller Roller diameter: 100-110mm (3.93-4.33in) Suitable bikes: All bikes with a wheel diameter of 26 to 29 in SPECIFICATIONS Max. footprint (lxw): 1350 x 470 mm (53 x 18.5 in) Height: 135 mm (5.31 in) Dimensions when folded: 800 × 470 × 135 mm (31.5 × 18.5 × 5.31 in) Weight: 7.7 kg (17.0 lbs) Trainer Type: Basic , Roller Article number: T1000
Kinetic Control Power Unit
$545.98
The Kinetic Control Power Unit installs in minutes and is the most affordable and convenient option for upgrading any Kinetic Rock and Roll or Road Machine trainer frame to our most advanced, interactive, app-controlled power training experience. It's part of our newest generation of interactive, app-controlled trainers offering the best power training workouts available, and features ANT+ FE-C and Bluetooth FTMS compatibility along with a more accurate and responsive ride. A massive 12-pound flywheel provides a realistic road feel with interactive, automatically-controlled resistance, super-quiet operation, and accurate and reproducible data. It works with apps like Kinetic Fit, Zwift, TrainerRoad, Rouvy, Kinomap, The Sufferfest, FulGaz and more. - Includes a free 6-month subscription for the Kinetic Fit power-training app - Works with Kinetic Fit, Zwift, and TrainerRoad on Bluetooth-connected smartphones, tablets, and laptops - Controlled resistance to simulate terrain changes in workouts and on virtual courses - Pairs with devices using Bluetooth Smart - Max slope: 10% - Max resistance: 1800 watts at 30mph - ±3% accuracy - Retrofits older Kinetic trainer frames - Easy to assemble - Unconditional one-year warranty on Power Unit
Page 1 of 1